Top 6 Zero Clearance Table Saw Insert UK – Table Saw Accessories

As an Amazon Associate I earn from qualifying purchases.

1. Peachtree Woodworking Supply

#ad

Peachtree Woodworking Supply 4133 Delta Phenolic Tablesaw Insert Zero Clearance

#ad
Peachtree Woodworking Supply #ad - Insert colors may vary from images shown. Zero clearance inserts help prevent tear out by essentially enveloping the blade on all sides which doesn’t allow the wood to tear out since there is not gap between the blade and insert. The opening is more like a custom slot cut to the exact width of your table saw blade.

Zero clearance inserts are table saw specific. Since every table saw brand and manufacturer is different, width and thickness of your table saw insert or opening and compare it to the size we list. This zero clearance insert is made from a high density phenolic material that was chosen for its ability to stand up to everyday workshop use. This is especially true when cutting plywood. Without a zero clearance, the wood has no support by the blade to prevent the wood from tearing out. We recommend that you use separate zero clearance inserts for dado blades since the gap for dados will be much wider than standard width table saw blades.

Zero clearance inserts can be used in conjunction with most any table saw blade including thin kerf, standard kerf and carbide tipped blades. Another great reason to use a zero clearance insert is to help reduce that pesky and irritating tear out you always tend to get on your cuts. Also be aware of the shape of your current insert of whether its round, we recommend that you measure the exact length, square ends or if there are any indents or protruding notches. The insert features two snug Fit sand-able side tabs that allow you to remove a little material at a time for a perfect fit if necessary.
BrandPeachtree Woodworking Supply #ad
ManufacturerFulton #ad
Part NumberAMZ-4133
Model4133

2. Leecraft

#ad

Leecraft DW-2 Zero-Clearance Table Saw Insert for DeWalt Model DW744 and DW746

#ad
Leecraft #ad - Measures 13-5/8-by-3-3/4 inches LxW. User-friendly with leveling and lateral adjustment screws, rear anti-life pin, and precut blade bottom pocket. Table saw insert for eWalt DW744 and DW746. Significantly reduces saw noise, dust, chip-out, and splintering. Constructed of high-density phenolic laminate with a bonded-melamine surface.
BrandLeecraft #ad
ManufacturerLeecraft #ad
Height35.18 cm (13.85 Inches)
Length11.05 cm (4.35 Inches)
Weight1.16
Width35.18 cm (13.85 Inches)
Part NumberDW-2
ModelDW-2

3. SKILSAW

#ad

SKILSAW SPT5004-ZC Zero Clearance Insert for Table Saw SPT99T

#ad
SKILSAW #ad - For precision cuts at 90°. Designed specifically to fit the SKILSAW SPT99T table saw. Reduces kerf clearance to the thickness of the blade. Designed for skilsaw spt99t Portable Worm Drive Table Saw.
BrandSKILSAW #ad
ManufacturerSKILSAW #ad
Part NumberSPT5004-ZC
ModelSPT5004-ZC

4. Leecraft

#ad

Leecraft CR-2 Sears Older 10-Inch Belt-Drive Zero Clearance Table Saw Insert Colors May Vary

#ad
Leecraft #ad - Greatly reduced chip-out and splintering. Supports work right up to the blade. Elimantes dangerous gap around blade where thin off-cuts can get wedged.
BrandLeecraft #ad
ManufacturerLeecraft #ad
Height2.54 cm (1 Inches)
Length35.56 cm (14 Inches)
Weight1.2
Width10.16 cm (4 Inches)
Part NumberCR-2
ModelCR-2

5. Delta

#ad

DELTA 36-862 Zero Clearance Table Insert for Left Tilt Unisaws and Contractor Saws

#ad
Delta #ad - Features four leveling screws and a width adjusting screw for a tight, flush fit. Designed for Delta contractor saws and left tilt unisaws. Constructed of phenolic material. Zero clearance Insert for 10-inch Saws. Provides for minimal clearance, giving the maximum support to materials being cut.
BrandDelta #ad
ManufacturerDelta #ad
Height1.6 cm (0.63 Inches)
Length36.83 cm (14.5 Inches)
Weight0.52 kg (1.15 Pounds)
Width11.43 cm (4.5 Inches)
Part Number36-862
Model36-862

6. Bosch

#ad

Bosch TS1012 Zero Clearance Insert GTS1031,Red

#ad
Bosch #ad - Reduces kerf clearance to the thickness of your blade. Zero clearance insert for Bosch GTS1031 only. Use for precision cuts at 90-degrees and reduces kerf clearance to thickness of blade. Supports the work-piece closer to blade for less chip-out and splintering.
BrandBosch #ad
ManufacturerBosch #ad
Height1.55 cm (0.61 Inches)
Length45.72 cm (18 Inches)
Weight0.17 kg (0.38 Pounds)
Width10.24 cm (4.03 Inches)
Part NumberTS1012
ModelTS1012